All

  • Applicable scope:

    1 every time before work, after work, to clean the work site and machine tools, so that the machine does not accumulate inside the chip, no stains on the ground without waste water, no debris on the control cabinet, keep the machine clean.
    2 carved machine every day before work must check the refrigerator temperature (about 2-3 degrees lower than room temperature) storage and coolant (if the water is too small, you need to add pure water), to ensure the cooling water cooler after opening unobstructed.
    3 check the working condition of positive pressure seal before work every day, the air pressure is 0.1-0.15MPa, the lower end of the main shaft has a uniform airflow (every hour need to be checked).
    4 each tool change, clean up the spindle motor casing, shaft, nut, tool clamping head scraps and powder, avoid dust suction motor caused by motor damage in cleaning machine must ensure open positive pressure sealing.
    5 after cleaning fixture scraps cooling tank top; every day before work, the filter needs cleaning the cooling box at the rear (found coolant effluent is small, also need to clean the filter), in order to ensure the normal circulation of cooling liquid.
    6 And stop every time before work, stop the spindle, with a clean cloth to wipe the dirt to the lower end of the main shaft.
    7 for important parts, must be treated with rust.

  • Applicable scope:

    1 The following work carried out once a month, in the maintenance process, the need to ensure the opening of positive pressure seal.Open the door, 1 X Y, the Z axis of the cover, the tiger skin, it will retract, and then clean up the screw and guide rail on the chip and dirt; manual to guide screw, gas reciprocating minutes, several times, will be out of the dirty oil to clean up; the process is repeated two to three times. Finally, clean the waste under the table.
    2 check the screw nut screw and nut seat and screw at the front and rear mount looseness; check the coupling screw loose. Manual to the lead screw, rail refueling, the refueling process will be X, Y, Z axis of the full stroke reciprocating several times so that the lubricant can be evenly attached to the surface of the moving parts.
    3 check the optical inspection and trip switch wiring loose, whether the connection is reliable; light check block and stroke switch block position is changed, the screw is loose, whether or not with other parts scratch phenomenon.
    4 Hand carved machine push pull, shake the Z shaft connecting plate, screw head and Z shaft plate check for loose screws; check the towline board and Z shaft connecting plate fixed loose.
     

  • Applicable scope:

    1, the machine must be checked and confirmed that the cooling system of the motor in the carving and engraving process (pump) and lubrication system (pump) is working properly; 
    2,The spindle carved machine rotates it is strictly prohibited to touch, to avoid accidental injury; 
    3, pay attention to clean up debris often movement carved machine box body, in order to ensure the normal work of the machine; 
    4, clamping the workpiece must be installed according to the actual, mounted, flat principle, is strictly prohibited in the material on the sculpture; in order to prevent the deformation of the material, the thickness of the material than the depth of the sculpture in 2mm above; 
    5, CNC engraving machine in the clamping tool before the clamping head within the debris to clean up; 
    6, the tool clamping, must first be card is screwed with the locking nut is placed, assembled to the engraving machine spindle, the tool is inserted into the card first, then the upper knife wrench slowly locking nut; handling tools, elastic nut disable push-pull mode, with rotation; 
    7, the machine tool with clamping head length according to the engraving depth, workpiece and fixture whether interference is determined, to meet the above conditions to take short; 
    8, Beam and plate carved machine machine is prohibited to place anything, to avoid falling injuries; 
    9, CNC engraving machine operation process, prohibited personnel lying on the machine to push, but not allowed to sit or lean on the machine; 10, carved machine processing must be the correct definition of X, Y, Z axis of the knife point, the tool is changed, must immediately redefine Z axis tool, X Y axis tool start point can not be changed; 
    11, the use of Microset definition knife point is prohibited engraving machine spindle rotation, to prevent the bad bar tool, forbidden to tool injection, oiling, not needing a cup will Microset cover; 
    In 12, carved machine start processing (knife), to put his hands on the machine red emergency switch, an accidental conditions immediately press; 
    13, when the knife is strictly prohibited to use a wrench to knock the card head; 
    14, after processing to turn off the power, the machine of workpiece inspection, packing tools, measuring tools, cleaning machine carved machine and ground, fill in "equipment records". 
    The above practical carved machine safety operation specifications issued by Shenzhen Yuanyang Xiangrui Machinery Co. Ltd, finishing, only to learn the reference, please indicate the source. 

     

firstprevious1234nextlast
400-000-000

在线客服

服务时段:9:00--18:00

扫一扫,马上浏览